Skip to Content
Stocking distributor & technical reseller|Mississauga, Ontario|Since 1990905-828-6022|Toll-free 1-866-396-2701|info@dymarchem.com

Bostik · anaerobic adhesives & sealants

Bostik threadlockers and sealants, matched to your Loctite numbers

Bostik’s Born2Bond anaerobic range locks, seals and retains metal parts. Anaerobics stay liquid in the bottle and cure only once they’re trapped between metal surfaces, away from air. Send us the Loctite grade you use and we’ll give you the Bostik equivalent.

ThreadlockersRetaining compoundsPipe sealantsGasket makers
1:1equivalents for common Loctite grades
4 jobslock, seal, form gaskets, retain
−55 to 230 °Cservice range across the grades
50–300 mlbottles, tubes and cartridges

Threadlockers

Stop bolts, studs and set screws from loosening under vibration. Pick the strength by how easily the part has to come apart again.

GradeStrengthColourUp to threadTemperature
TA-22Low (easy removal)PurpleM20−55 to 180 °C
TA-43Medium (hand tools)BlueM36−55 to 180 °C
TA-70High (permanent)GreenM20−55 to 180 °C
TA-90Wicking, very low viscosityGreenM6−55 to 150 °C

TA-90 wicks into threads that are already assembled.

Retaining compounds

Bond bearings, bushings, sleeves and gears onto shafts and into housings, so press fits can be looser and still hold.

GradeStrengthMax gapTemperature
RA-38High0.2 mm−55 to 180 °C
RA-48High0.15 mm−55 to 180 °C
RA-20High, heat resistant0.2 mm−55 to 230 °C
RA-03High0.1 mm−55 to 150 °C
RA-41Medium0.1 mm−55 to 150 °C
RA-60High, paste for worn parts0.5 mm−55 to 150 °C

Pipe and thread sealants, gasket makers

GradeUseColourLimit
Pipe and thread sealants
PA-42Low viscosity, for finer threadsBrownUp to M36, −55 to 150 °C
PA-77High viscosity, for large pipe threadsYellowUp to M80, −55 to 180 °C
Gasket makers for rigid flanges
GA-10Form-in-place gasketPinkGaps to 0.25 mm
GA-18Form-in-place gasketRedGaps to 0.25 mm
GA-74Form-in-place gasketOrangeGaps to 0.3 mm

Most grades come in 50 ml and 250 ml bottles; gasket makers in 50 ml packs, 250 ml tubes and 300 ml cartridges. Figures from Bostik data sheets; we send the current sheet with your quote.

Switching from Loctite

Most plants already have Loctite numbers in their maintenance procedures. Send us the list and we’ll match each one to a Bostik grade with the same strength, viscosity and cure, so your procedures don’t need rewriting.

Have a list of Loctite part numbers? Send it over and we’ll reply with the Bostik match and a price for each.

Match my Loctite list

Questions

How long do anaerobics take to cure?

They grip within minutes on clean steel and reach full strength over about a day at room temperature. Cold shops, inactive metals such as stainless or plated parts, and wide gaps slow it down; a primer speeds it up.

Which threadlocker for bolts I’ll need to remove?

Low or medium strength: TA-22 for small fasteners, TA-43 for general use. Both come apart with ordinary hand tools. TA-70 is for parts that should stay put.

Do they work on plastic?

Anaerobics are made for metal parts. For plastics, tell us the materials and we’ll recommend another adhesive.

Related

Talk to a specialist

Cross-references, food-grade approvals and hard-to-find specs. Let’s talk.

Tell us what you’re running today. If it’s not on this site, we can usually still get it.