Skip to Content
Stocking distributor & technical reseller|Mississauga, Ontario|Since 1990905-828-6022|Toll-free 1-866-396-2701|info@dymarchem.com

Halocarbon

Halocarbon PCTFE: the fluid for chlorine and Lewis acids

Polychlorotrifluoroethylene oils, greases and waxes are nonflammable and chemically inert, with no oxygen in the molecule. That makes them the safer choice where reactive gases and Lewis acids would slowly break down other fluorinated fluids.

NonflammableOxygen compatibleChlorine serviceOils, greases, waxes
0%weight loss after AlCl3 exposure (PFPE: 16–17%)
3 formsoils, greases and waxes from one chemistry
−60 to 399 °Cgrease range, by grade
Pamphlet 164MT-3I thread sealant, Chlorine Institute listing

Why PCTFE holds up where PFPE doesn’t

Both chemistries are inert and nonflammable. The difference shows up with Lewis acids such as aluminum trichloride, boron trichloride and iron or zinc chlorides, which form in chlorinated and fluorinated etch and deposition processes and can reach a pump’s oil.

After 24 h at 174 °C with 1% AlCl3PCTFE (Halocarbon)PFPE
WeightNo loss16–17% loss
AcidityNo increaseIncreased
ViscosityNo reductionSignificant loss

Source: Halocarbon test data, nitrogen atmosphere.

Oils by application

Grade numbers roughly follow viscosity: low numbers stay fluid in the cold and in instruments, high numbers carry heavier loads.

ApplicationGradesWhy
Instrument fill and pressure devicesHalocarbon 1.8, 4.2, 6.3Low viscosity for fast, stable readings
Cold equipmentHalocarbon 4.2, 6.3, 27Stay fluid where hydrocarbon oils thicken
Pumps and compressors, including chlorineHalocarbon 27, 56, 95, 200Recommended by Halocarbon for chlorine pumps and compressors
Reactive-gas vacuum (roughing pumps)Halocarbon HaloVac 60, 100, 125Low vapour pressure for etch and deposition tools
Heavy load and heatHalocarbon 200, 400, 700Heavier viscosity and film strength
Mechanical sealsMSHV06, MSLV27, MSLV56Barrier fluids that stay stable and carry heat away from seal faces

Greases and waxes

GradeTypeService temp.Best for
PCTFE greases: valves, gaskets, threads
Halocarbon 25-5SSilica, NLGI 2–3−20 to 175 °CValves and gaskets; MIL-G-47219A
Halocarbon 25-10MPCTFE polymer, NLGI 10 to 135 °CSoftest grade, won’t separate oil; where silica is a concern
Halocarbon 25-20MPCTFE polymer, NLGI 4−5 to 150 °CHardest grade
Halocarbon X90-10M, 28LTNLGI 1 and 2Down to −40 and −45 °CValves and seals that must move in the cold
Halocarbon MT-3IPTFE with molybdenum, NLGI 3−20 to 175 °CThread sealant and anti-galling for chlorine connectors (Chlorine Institute Pamphlet 164)
Halocarbon HaloVac 25Silica, NLGI 3−20 to 175 °CLab vacuum, stopcocks, glass and ceramic joints
InfinX™ PFPE greases by Halocarbon: bearings and high heat
InfinX™ MRO KF205, KF206, KF207PTFE, NLGI 2To 204, 260 and 288 °CHot bearings; KF205 is NSF H1
InfinX™ MRO KF407Silica, NLGI 2−10 to 399 °CUltra-high temperature
InfinX™ AERO KFMS3PTFE, NLGI 2−40 to 260 °CMIL-PRF-27617G Type III, cryogenic gas and liquid
PCTFE waxes: sealing and lab use
Halocarbon Wax 40, 600, 1500PCTFE waxMelting points to 132 °C (Wax 1500)Chemically resistant thread sealing and laboratory work

Typical values from Halocarbon data sheets. We send the current sheet with your quote.

Where it’s used

Chlorine and chlor-alkali

Pumps, compressors, valves and threaded connectors in chlorine service.

Semiconductor

Roughing pumps on chlorinated and fluorinated etch and deposition processes.

Oxygen and gas handling

Valves, regulators and O-rings where hydrocarbons are a fire risk.

Instruments and thermal control

Diaphragm seals, pressure-device fill fluids, calibration baths and chillers.

Questions

Should I use Halocarbon or Krytox™?

For chlorine, Lewis acids and many reactive chemicals, PCTFE (Halocarbon) is the better fit. For high-temperature bearings, oxygen and most semiconductor vacuum work, PFPE (Krytox™) is common. We carry both, so we’ll recommend on the process, not the brand.

Can PCTFE oil go into a pump that ran hydrocarbon oil?

Only after the pump is stripped and cleaned. Fluorinated fluids and hydrocarbon oils don’t mix.

Do you have food-grade Halocarbon greases?

Yes. Several InfinX™ PFPE greases by Halocarbon, including InfinX™ MRO KF205, are NSF H1 registered.

Related

Talk to a specialist

Cross-references, food-grade approvals and hard-to-find specs. Let’s talk.

Tell us what you’re running today. If it’s not on this site, we can usually still get it.